FAQ'S Service
Service Questions


一、A series laser instructions and matters needing attention

operating steps

1. The laser and the power connection between connected and tighten the screw.

2. Please insert the power cord end before starting the power supply panel interface, the other end connected to 220 v power supply.
3. Open the laser power switch, after a few seconds laser emitted.
4. If you need to adjust the power, and could be controlled by adjusting the current of your laser lock when stable temperature control in the factory.
5. If you want to access the TTL signal, need to first line plug on the received signal generator (5 VDC output), the red line to the positive, negative black line, select the appropriate frequency, and then insert the line after the laser power supply panel jacks, can obtain the laser modulation, signal plug pulled out, can restore the continuous laser.
6. Need to shut down the laser directly close the laser power supply switch.
Matters needing attention
1. To prevent injury and person, please do not use laser direct illuminate in person especially on the human eye.
2. The laser power, the power supply wire sealed with laser.
3. Such lasers are more sensitive to temperature, when using must ensure good heat dissipation, as far as possible on the heat dissipation good metal plane.
4. The laser can only receive 5 VDC modulation signal.
5. Do not use for a long time, please place the laser in moisture-proof, anti-static place.
6. Need to avoid severe impact damage to the laser.
7. Remove and modified laser and power supply is not allowed while visiting, once the company shall not be liable for any losses incurred.


二、VB series laser instructions and matters needing attention

operating steps

1. Please send the power cord access before starting the 220 v power supply.
2. After a few seconds, turning on the power supply of laser.
3. If you want to access the TTL signal, need to first line plug on the received signal generator (5 VDC output), insert the line within the plug of the panel after laser, can obtain the laser modulation, signal plug pulled out, can restore the continuous laser.
4. Close the laser directly off to the supply required.

announcements
1. For your safety, please do not use laser direct illuminate in person especially on the human eye.
2. Such lasers are more sensitive to temperature, when using must ensure good heat dissipation, as far as possible on the heat dissipation good metal plane.
3. The laser can only receive 5 v TTL DC modulation signal.
4. Do not use for a long time, please put the laser in moisture-proof, anti-static place.
5. Avoid violent collision, otherwise it will cause damage of laser.
6. Remove and modified laser is not allowed while visiting, which shall not be responsible for all the losses resulting from the company


三、About the product warranty


1. Everyone in my company (and authorized agents) to purchase the laser device products in the correct use of cases, by the card shall have a one-year warranty service;Were it not for the warranty conditions, company can also provide maintenance fee according to actual condition.
2. In the following cases to be outside the scope of free warranty, please note.
(1) there is no warranty card or the product serial number
(2) the forbidden tag down the damaged or there is a clear traces to tear open outfit.
(3) the product is to replace components or customized products required components, without permission to remove or replace elements lead to problems.
(4) the improper use or improper repair, renovation and failure or damage.
(5) not used in accordance with the instructions or environmental damage.
(6) by acquiring a strong impact in the process of installation or handling damage.
(7) for repair and replacement, guarantee no delay
(8) laser power according to the normal life, slow attenuation is not in the scope of free warranty
(9) warranty card must truthfully fill in with my company or agent seal can take effect.
(10) for a fire, earthquake, flood, lightning and other natural disasters or the power supply voltage is not normal fault and damage.
3. The company reserves the right to the interpretation of the above terms and conditions.If the products appear problem, please contact the company (or agent), we will in the shortest possible time to solve it.At the same time also sincerely hope you can to our company's products put forward valuable opinions and Suggestions, we will spare no effort to improve our products.

 
address:Beijing Changping District Shahe town Changping Road No. 97 Xinyuan science and Technology Park, 8 block A 4 floor 401
phone: 010-80703749
Email:Sales@viasho.com
邮编:330520
Copyright ©2005 - 2013 北京榜首科技有限公司2
犀牛云提供企业云服务


X
1

QQ设置

3

SKYPE 设置

4

阿里旺旺设置

5

电话号码管理

  • 010-80703749
6

二维码管理

Top
展开